Recycled filament

How to use the Filament Maker

This guide turns a prepared PET bottle, wound onto the Strip Spool, into a spool of 1.75mm rPET filament. The photos show the original Filament Maker. The Filament Maker V2 has significant improvements, but it makes filament the same way: the same temperature and the same steps.

The nozzle bracket of a Sustainable Design Studio Filament Maker with filament passing through it.
The strip goes in flat and comes out as filament.
Before you start

What you need

Start with a bottle already cut into a strip and wound onto the Strip Spool. The rest is ordinary workshop kit.

Workshop tools

  • Pliers, to pull the tail through the nozzle
  • Snips, to trim the finished filament
  • A filament dryer or dehydrator. Fresh filament needs drying before it is stored or printed
  • A fume extractor, or at least a well-ventilated space

PPE

  • Protective gloves, against the hot nozzle and the sharp edge of the strip
  • Safety goggles, worn for every step. See Basic PPE
  • A respirator, against the fumes while the machine runs
The process

Step by step filament making

Two parts. First you load the strip into the cold machine, then you heat the nozzle and let the Pulley Spool draw it through. The photos show the original Filament Maker; on the Filament Maker V2 the controls look different, but the temperature and the process are the same.

Part 1

Load the strip

Everything here happens with the machine off and the nozzle cold.

  1. A pair of cut-resistant gloves and a pair of safety goggles on a workbench.
    Step 1

    Put on your PPE

    Wear protective gloves and safety goggles for every step, and a respirator while the machine is running.

  2. Step 2

    Check the machine is off and cool

    Make sure the Filament Maker is switched off and the nozzle is cold before you load anything.

  3. A gloved hand placing the loaded Strip Spool on its spindle beside the nozzle bracket.
    Step 3

    Load the Strip Spool

    Place the loaded Strip Spool on the machine so the strip comes off the top right of the spool, turning clockwise.

  4. The Filament Maker on a workbench with the loaded Strip Spool, the nozzle bracket and the empty Pulley Spool.
    Step 4

    Feed the tail through the cold nozzle

    Feed the thin tail of the strip into the cold nozzle until it just pokes out of the other side.

  5. Pliers gripping the tail of the strip where it comes out of the nozzle.
    Step 5

    Pull the tail through about 3cm

    Grip the tail with pliers and pull it through the nozzle by about 3cm.

Part 2

Make the filament

Bring the nozzle up to 210°C, start the Pulley Spool, and stay with the machine until the strip runs out.

  1. A gloved hand holding the tail with pliers at the nozzle while the machine heats up.
    Step 6

    Heat the nozzle to 210°C

    Switch on your fume extraction, then switch on the Filament Maker and set it to 210°C. The controls differ between the original machine and the Filament Maker V2, so follow the user guide that came with yours.

    Keep hold of the tail with the pliers while the nozzle comes up to temperature.

  2. Pliers drawing the new filament out of the nozzle towards the Pulley Spool.
    Step 7

    Pull about 20cm towards the Pulley Spool

    Once the machine reaches 210°C, pull the tail about 20cm towards the Pulley Spool. It should come fairly easily. If there is a lot of resistance, the strip is probably the wrong width for the bottle, so check the spacers against the wall thickness.

  3. The end of the new filament fed into the black Pulley Spool beside its protector post.
    Step 8

    Feed the filament into the Pulley Spool

    Feed the end into the Pulley Spool. Pull far enough first that the part going into the spool is already formed 1.75mm filament, not flat strip. Formed filament grips, and a flat strip tends to slip out.

  4. A gloved hand turning the blue motor speed knob on the front of the Filament Maker.
    Step 9

    Run the motor at full speed

    Turn the motor up to its maximum speed. The Pulley Spool now draws the strip through the nozzle and winds the filament on.

  5. The Filament Maker running, with the Strip Spool feeding the nozzle and filament winding onto the Pulley Spool.
    Step 10

    Stay with the machine

    Do not leave the Filament Maker running unattended. Keep your face and eyes away from the nozzle while it works.

  6. A gloved hand holding the last of the strip just before it enters the nozzle.
    Step 11

    Catch the end before it leaves the nozzle

    As the strip runs out, grab the filament at its end before it exits the nozzle. If it gets away, it can whip out and unspool.

  7. A gloved hand tucking the loose end of the filament into the Pulley Spool.
    Step 12

    Tuck the end into the Pulley Spool

    Feed the loose end into the Pulley Spool so the spool cannot unwind.

  8. A gloved hand lifting the filled Pulley Spool off the Filament Maker.
    Step 13

    Take the Pulley Spool off

    Switch off the motor and remove the full Pulley Spool from the machine.

  9. Snips trimming the end of the filament on the finished spool.
    Step 14

    Trim both ends

    Snip off both ends of the filament.

  10. The finished spool being placed into a filament dryer.
    Step 15

    Dry the filament

    Dry the new spool in a dehydrator at 60°C for about 3 hours. PET absorbs moisture from the air, and damp filament prints badly. Dry it again before printing, as the print settings guide explains.

FAQ

Making filament, answered

Question not covered here? The team replies within one to two working days. Get in touch

Filament from the Filament Maker is a hollow tube, not a solid strand, and the print settings allow for that. The best results look like a spiral, where the strip tucks into itself. If the strip is too narrow for the bottle it will not close into a loop and you get a C shape. Too wide and it doubles back on itself. Both come from the strip width, so measure every bottle and set the cutter to match.
A lot of resistance when you pull the first 20cm usually means the strip is the wrong width for the bottle. Check the wall thickness again with callipers and fit the matching spacers: 10mm for a 0.1mm wall, 9mm for 0.2mm, 8mm for 0.3mm.
Label residue. If a bottle is not cleaned properly, the glue burns in the nozzle and sticks to the filament as it is pulled through. Clean every bottle before cutting. If the problem continues, switch the machine off, let it cool, and clean out the nozzle with tissue or a cotton bud.
Yes. The Filament Maker gives off a fair amount of fumes while it runs. Use it in a well-ventilated space, run a fume extractor, and wear a respirator.
Protective gloves, against the heat of the nozzle and the sharp edges of the strip. Safety goggles. And a respirator, against the fumes.
Just under 12 hours of machine time. On average the Filament Maker makes about 14g of filament every 10 minutes, and a 1kg spool takes around fifty 2L bottles. Running in batches rather than heating and cooling the machine for each bottle saves time.
We recommend a soldering iron and the filament joiner, as shown in the filament joining guide. Without a soldering iron, you may be able to use the hot nozzle of the Filament Maker instead.

Filament not coming out right?

Send us a photo of the filament and the bottle it came from. We’ll help you work out what is going wrong.